The influence of the production process on mechanical properties of rubber testing samples

Škrobák, Adam; Staněk, Michal; Maňas, David; Ovsík, Martin; Šenkeřík, Vojtěch; Řezníček, Martin

dc.title	The influence of the production process on mechanical properties of rubber testing samples	en
dc.contributor.author	Škrobák, Adam
dc.contributor.author	Staněk, Michal
dc.contributor.author	Maňas, David
dc.contributor.author	Ovsík, Martin
dc.contributor.author	Šenkeřík, Vojtěch
dc.contributor.author	Řezníček, Martin
dc.relation.ispartof	Advanced Materials Research
dc.identifier.issn	1022-6680 Scopus Sources, Sherpa/RoMEO, JCR
dc.identifier.isbn	978-3-03-835254-9
dc.date.issued	2014
utb.relation.volume	1025-1026
dc.citation.spage	37
dc.citation.epage	41
dc.event.title	2014 International Conference on Advanced Materials, Structures and Mechanical Engineering, ICAMSME 2014
dc.event.location	Jeju Island
utb.event.state-en	South Korea
utb.event.state-cs	Jižní Korea
dc.event.sdate	2014-05-03
dc.event.edate	2014-05-04
dc.type	conferenceObject
dc.language.iso	en
dc.publisher	Trans Tech Publications Ltd.
dc.identifier.doi	10.4028/www.scientific.net/AMR.1025-1026.37
dc.relation.uri	http://www.scientific.net/AMR.1025-1026.37
dc.subject	injection molding	en
dc.subject	compression molding	en
dc.subject	mechanical properties	en
dc.subject	rubber	en
dc.subject	test sample	en
dc.description.abstract	The article deals with the influence of production technology on mechanical properties of rubber testing samples. In practice, rubber testing samples are cut out from a compression molded sheet, also in case of testing of rubber compounds appointed for injection molding. However, the different way of the preparation of testing samples and the production itself may have a negative effect on the mechanical properties of the final product. Thus the article judges, to what extent the mechanical properties (tensile strength, extension, tear strength and microhardness) of testing samples from selected rubber materials are influenced by injection molding, and evaluates the possible divergence.	en
utb.faculty	Faculty of Technology
dc.identifier.uri	http://hdl.handle.net/10563/1003946
utb.identifier.obdid	43872245
utb.identifier.scopus	2-s2.0-84913558170
utb.source	d-scopus
dc.date.accessioned	2015-01-13T09:25:53Z
dc.date.available	2015-01-13T09:25:53Z
dc.rights.access	openAccess
utb.contributor.internalauthor	Škrobák, Adam
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Ovsík, Martin
utb.contributor.internalauthor	Šenkeřík, Vojtěch
utb.contributor.internalauthor	Řezníček, Martin
utb.fulltext.affiliation	Adam Skrobak1, a, Michal Stanek1,b, David Manas1,c, Martin Ovsik1,d, Vojtech Senkerik1,e, Martin Reznicek1,f 1 Tomas Bata University in Zlin, TGM 5555, 760 01 Zlin, Czech Republic a skrobak@ft.utb.cz, b stanek@ft.utb.cz, c dmanas@ft.utb.cz, d ovsik@ft.utb.cz, e vsenkerik@ft.utb.cz, f mreznicek@ft.utb.cz
utb.fulltext.dates	-
utb.fulltext.references	[1] Sezna, J. A. (1993). Rubber testing for injection molding. Rubber World, 207(4), 12-19. [2] Arrillaga, A., Zaldua, A. M., & Farid, A. S. (2012). Evaluation of injection-molding simulation tools to model the cure kinetics of rubbers. Journal of Applied Polymer Science, 123(3), 1437-1454. [3] W.C. Oliver, G.M. Pharr, Measurement of Hardness and Elastic Modulus by Instrumented Indentation. Journal of Materials Research 19 (1), (2004), 1564-1583
utb.fulltext.sponsorship	This paper is supported by the internal grant of TBU in Zlin No. IGA/FT/2014/016 funded from the resources of specific university research and by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089.
utb.fulltext.projects	IGA/FT/2014/016
utb.fulltext.projects	CZ.1.05/2.1.00/03.0089
utb.fulltext.faculty	-
utb.fulltext.ou	-