The Influence of runner system on production of injection molds

Janoštík, Václav; Staněk, Michal; Maňas, David; Maňas, Miroslav; Šenkeřík, Vojtěch

dc.title	The Influence of runner system on production of injection molds	en
dc.contributor.author	Janoštík, Václav
dc.contributor.author	Staněk, Michal
dc.contributor.author	Maňas, David
dc.contributor.author	Maňas, Miroslav
dc.contributor.author	Šenkeřík, Vojtěch
dc.relation.ispartof	MATEC Web of Conferences 20th International Conference on Circuits, Systems, Communications and Computers (CSCC 2016)
dc.identifier.issn	2261-236X Scopus Sources, Sherpa/RoMEO, JCR
dc.date.issued	2016
utb.relation.volume	76
dc.event.title	20th International Conference on Circuits, Systems, Communications and Computers (CSCC)
dc.event.location	Corfu
utb.event.state-en	Greece
utb.event.state-cs	Řecko
dc.event.sdate	2016-07-14
dc.event.edate	2016-07-17
dc.type	conferenceObject
dc.language.iso	en
dc.publisher	EDP Sciences
dc.identifier.doi	10.1051/matecconf/20167602022
dc.relation.uri	https://www.matec-conferences.org/articles/matecconf/abs/2016/39/matecconf_cscc2016_02022/matecconf_cscc2016_02022.html
dc.description.abstract	This experimental study describes the influence of runner system on rheological properties during the injection molding process. Economic effects on the amount of production are discussed as well. Autodesk Moldflow Synergy 2016 (Moldflow) was used for the study of the injection process. Three suggestions of the runner system, cold runner system, hot runner system and the combination of cold hot runner system have been promoted. These three variants underwent the rheological and economic analysis. As a result, recommendations for the application of the runner system for the required amount of production have been suggested.	en
utb.faculty	Faculty of Applied Informatics
dc.identifier.uri	http://hdl.handle.net/10563/1006992
utb.identifier.obdid	43875897
utb.identifier.scopus	2-s2.0-85016104551
utb.identifier.wok	000392332200035
utb.source	d-wok
dc.date.accessioned	2017-07-13T14:50:30Z
dc.date.available	2017-07-13T14:50:30Z
dc.description.sponsorship	Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme [LO1303 (MSMT-7778/2014)]; European Regional Development Fund under the project CEBIA-Tech [CZ.1.05/2.1.00/03.0089]; TBU in Zlin [IGA/FT/2016/010]
dc.rights	Attribution 4.0 International
dc.rights.uri	https://creativecommons.org/licenses/by/4.0/
dc.rights.access	openAccess
utb.contributor.internalauthor	Janoštík, Václav
utb.contributor.internalauthor	Staněk, Michal
utb.contributor.internalauthor	Maňas, David
utb.contributor.internalauthor	Maňas, Miroslav
utb.contributor.internalauthor	Šenkeřík, Vojtěch
utb.fulltext.affiliation	Vaclav Janostik 1,a , Michal Stanek 1 , David Manas 1 , Miroslav Manas 1 and Vojtech Senkerik 1 1 Tomas Bata University in Zlin, TGM 5555, 760 01 Zlin, Czech Republic a Corresponding author: vjanostik@ft.utb.cz
utb.fulltext.dates	-
utb.fulltext.sponsorship	This work was supported by the Ministry of Education, Youth and Sports of the Czech Republic within the National Sustainability Programme project No. LO1303 (MSMT-7778/2014) and by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089 and also by the internal grant of TBU in Zlin No. IGA/FT/2016/010 funded from the resources of specific university research.