Kontaktujte nás | Jazyk: čeština English
dc.title | Influence of injection moulding process parameters on high-density polyethylene surface hardness | en |
dc.contributor.author | Mizera, Aleš | |
dc.contributor.author | Fiala, Tomáš | |
dc.contributor.author | Maňas, Miroslav | |
dc.contributor.author | Stoklásek, Pavel | |
dc.contributor.author | Ovsík, Martin | |
dc.relation.ispartof | Materials Science Forum | |
dc.identifier.issn | 0255-5476 Scopus Sources, Sherpa/RoMEO, JCR | |
dc.date.issued | 2020 | |
utb.relation.volume | 994 | |
dc.citation.spage | 189 | |
dc.citation.epage | 196 | |
dc.type | article | |
dc.language.iso | en | |
dc.publisher | Trans Tech Publications Ltd | |
dc.identifier.doi | 10.4028/www.scientific.net/msf.994.189 | |
dc.relation.uri | https://www.scientific.net/MSF.994.189 | |
dc.subject | depth-sensing indentation | en |
dc.subject | high-density polyethylene | en |
dc.subject | injection moulding | en |
dc.subject | nano-hardness | en |
dc.subject | surface properties | en |
dc.description.abstract | Commodity polymers are a common part of everyday life. They consist mainly of polyolefins such as polyethylene, polypropylene. They are primarily used for ease of processing, cost and especially chemical resistance. The disadvantages of these polymers are low mechanical properties as well as temperature resistance. Any improvement in the mechanical properties can extend the application possibilities of the commodity polymers to the areas reserved for the construction polymers. This paper deals with changing two injection moulding process parameters-melt and mould temperature to high-density polyethylene (HDPE) surface hardness. HDPE hardness was measured using the method of Depth-Sensing Indentation (DSI) on three different instruments (ultranano-, nano- and micro-hardness tester). It has been found that as the melt and mould temperature increases, the hardness slightly increases. © 2020 Trans Tech Publications Ltd, Switzerland. | en |
utb.faculty | Faculty of Applied Informatics | |
dc.identifier.uri | http://hdl.handle.net/10563/1009777 | |
utb.identifier.obdid | 43881290 | |
utb.identifier.scopus | 2-s2.0-85086760271 | |
utb.identifier.coden | MSFOE | |
utb.source | j-scopus | |
dc.date.accessioned | 2020-07-10T13:51:21Z | |
dc.date.available | 2020-07-10T13:51:21Z | |
utb.ou | CEBIA-Tech | |
utb.contributor.internalauthor | Mizera, Aleš | |
utb.contributor.internalauthor | Maňas, Miroslav | |
utb.contributor.internalauthor | Stoklásek, Pavel | |
utb.contributor.internalauthor | Ovsík, Martin | |
utb.fulltext.affiliation | Ales Mizera 1,a*, Tomas Fiala 2,b, Miroslav Manas 1,c, Pavel Stoklasek 1,d, Martin Ovsik 1,e 1 Tomas Bata University in Zlin, nam. T.G. Masaryka 5555, 760 01, Zlin, Czech Republic 2 Tomas Fiala, Cejetice 59, 386 01, Strakonice, Czech Republic a* mizera@utb.cz b tomas.fiala@hotmail.cz c manas@utb.cz d pstoklasek@utb.cz e ovsik@utb.cz | |
utb.fulltext.dates | Submitted: 2019-11-08 Revised: 2019-11-28 Accepted: 2019-12-02 Online: 2020-05-27 | |
utb.fulltext.sponsorship | This paper is supported by the Ministry of Education Youth and Sports of the Czech Republic within the National Sustainability Programme project No. LO1303 (MSMT-7778/2014) and also by the European Regional Development Fund under the project CEBIA-Tech No. CZ.1.05/2.1.00/03.0089. | |
utb.scopus.affiliation | Tomas Bata University in Zlin, nam. T.G. Masaryka 5555, Zlin, 760 01, Czech Republic; Tomas Fiala, Cejetice 59, Strakonice, 38601, Czech Republic | |
utb.fulltext.projects | LO1303 | |
utb.fulltext.projects | MSMT-7778/2014 | |
utb.fulltext.projects | CZ.1.05/2.1.00/03.0089 |